100% Pass Top-selling NSE6_FWF-6.4 Exams - New 2024 Fortinet Pratice Exam
NSE 6 Network Security Specialist Dumps NSE6_FWF-6.4 Exam for Full Questions - Exam Study Guide
NEW QUESTION # 20
Refer to the exhibits.
Exhibit A
Exhibit B
A wireless network has been created to support a group of users in a specific area of a building. The wireless network is configured but users are unable to connect to it. The exhibits show the relevant controller configuration for the APs and the wireless network.
Which two configuration changes will resolve the issue? (Choose two.)
- A. Disable intra-vap-privacy for the Authors vap-wireless network
- B. For both interfaces in the wtp-profile, configure vap-all to be manual
- C. For both interfaces in the wtp-profile, configure set vaps to be "Authors"
- D. Increase the transmission power of the AP radio interfaces
Answer: B,C
NEW QUESTION # 21
Which of the following is a requirement to generate analytic reports using on-site FortiPresence deployment?
- A. SQL services must be running
- B. DTLS encryption on wireless traffic must be turned off
- C. Wireless network security must be set to open
- D. Two wireless APs must be sending data
Answer: D
Explanation:
FortiPresence VM is deployed locally on your site and consists of two virtual machines. All the analytics data collected and computed resides locally on the VMs.
NEW QUESTION # 22
Refer to the exhibits.
Exhibit A
Exhibit B
The exhibits show the diagnose debug log of a station connection taken on the controller CLI.
Which security mode is used by the wireless connection?
- A. WPA2 Enterprise
- B. WPA3 Enterprise
- C. Open, with radius MAC filtering
- D. WPA2 Personal and radius MAC filtering
Answer: D
NEW QUESTION # 23
As standard best practice, which configuration should be performed before configuring FortiAPs using a FortiGate wireless controller?
- A. Preauthorize APs
- B. Set the wireless controller country setting
- C. Create wireless LAN specific policies
- D. Create a custom AP profile
Answer: D
NEW QUESTION # 24
Which statement is correct about security profiles on FortiAP devices?
- A. Disable DTLS on FortiAP
- B. Only bridge mode SSIDs can apply the security profiles
- C. Security profiles on FortiAP devices can use FortiGate subscription to inspect the traffic
- D. FortiGate performs inspection the wireless traffic
Answer: B
NEW QUESTION # 25
You are investigating a wireless performance issue and you are trying to audit the neighboring APs in the PF environment. You review the Rogue APs widget on the GUI but it is empty, despite the known presence of other APs.
Which configuration change will allow neighboring APs to be successfully detected?
- A. Enable Radio resource provisioning on the relevant AP profiles.
- B. Enable Locate WiFi clients when not connected in the relevant AP profiles.
- C. Enable Monitor channel utilization on the relevant AP profiles.
- D. Ensure that all allowed channels are enabled for the AP radios.
Answer: A
Explanation:
Explanation
The ARRP (Automatic Radio Resource Provisioning) profile improves upon DARRP (Distributed Automatic Radio Resource Provisioning) by allowing more factors to be considered to optimize channel selection among FortiAPs. DARRP uses the neighbor APs channels and signal strength collected from the background scan for channel selection.
NEW QUESTION # 26
As standard best practice, which configuration should be performed before configuring FortiAPs using a FortiGate wireless controller?
- A. Preauthorize APs
- B. Create wireless LAN specific policies
- C. Set the wireless controller country setting
- D. Create a custom AP profile
Answer: C
NEW QUESTION # 27
Refer to the exhibit.
If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?
- A. Areas with the signal strength weaker than -68 dB are highlighted in orange and red to indicate that no signal was propagated by the APs.
- B. Areas with the signal strength equal to -68 dB are zoomed in to provide better visibility
- C. Areas with the signal strength equal or stronger than -68 dB are highlighted in multicolor
- D. Areas with the signal strength weaker than -68 dB are cut out of the map
Answer: C
NEW QUESTION # 28
When deploying a wireless network that is authenticated using EAP PEAP, which two configurations are required? (Choose two.)
- A. A WPA2 or WPA3 personal wireless network
- B. An X.509 certificate to authenticate the client
- C. An X.509 to authenticate the authentication server
- D. A WPA2 or WPA3 Enterprise wireless network
Answer: C,D
NEW QUESTION # 29
Refer to the exhibit.
What does the asterisk (*) symbol beside the channel mean?
- A. Indicates channels that will be scanned by the Wireless Intrusion Detection System (WIDS)
- B. Indicates channels that cannot be used because of regulatory channel restrictions
- C. Indicates channels that are subject to dynamic frequency selection (DFS) regulations
- D. Indicates channels that can be used only when Radio Resource Provisioning is enabled
Answer: C
NEW QUESTION # 30
Refer to the exhibit.
If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?
- A. Areas with the signal strength weaker than -68 dB are highlighted in orange and red to indicate that no signal was propagated by the APs.
- B. Areas with the signal strength equal to -68 dB are zoomed in to provide better visibility
- C. Areas with the signal strength equal or stronger than -68 dB are highlighted in multicolor
- D. Areas with the signal strength weaker than -68 dB are cut out of the map
Answer: C
NEW QUESTION # 31
Part of the location service registration process is to link FortiAPs in FortiPresence.
Which two management services can configure the discovered AP registration information from the FortiPresence cloud? (Choose two.)
- A. FortiAP Cloud
- B. AP Manager
- C. FortiGate
- D. FortiSwitch
Answer: A,C
Explanation:
FortiGate, FortiCloud wireless access points (send visitor data in the form of station reports directly to FortiPresence)
NEW QUESTION # 32
Which two statements about distributed automatic radio resource provisioning (DARRP) are correct? (Choose two.)
- A. DARRP performs continuous spectrum analysis to detect sources of interference. It uses this information to allow the AP to select the optimum channel.
- B. DARRP requires that wireless intrusion detection (WIDS) be enabled to detect neighboring devices.
- C. DARRP measurements can be scheduled to occur at specific times.
- D. DARRP performs measurements of the number of BSSIDs and their signal strength (RSSI). The controller then uses this information to select the optimum channel for the AP.
Answer: C,D
Explanation:
Explanation
According to Fortinet training: "When using DARRP, the AP selects the best channel available to use based on the scan results of BSSID/receive signal strength (RSSI) to AC" and "To set the running time for DARRP optimization, use the following CLI command within the wireless controller setting: set darrp-optimize
{integer}. Note that DARRP doesn't do continuous spectrum analysis..."
NEW QUESTION # 33
How can you find upstream and downstream link rates of a wireless client using FortiGate?
- A. On the FortiGate GUI, using the WiFi Client monitor
- B. On the FortiAP CLI, using the cw_diag ksta command
- C. On the FortiGate CLI, using the diag wireless-controller wlac -d Sta command
- D. On the FortiAP CLI, using the cw_diag -d sta command
Answer: A
Explanation:
Explanation
The WiFi Client monitor on the FortiGate GUI shows the upstream and downstream link rates of a wireless client, along with other information such as MAC address, SSID, IP address, signal strength, and connection time. The link rates indicate the maximum data rates that the client can achieve in both directions.
References: Secure Wireless LAN Course Description, page 7; [FortiOS 6.4.0 Handbook - Wireless Controller], page 37.
NEW QUESTION # 34
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit C
A wireless network has been installed in a small office building and is being used by a business to connect its wireless clients. The network is used for multiple purposes, including corporate access, guest access, and connecting point-of-sale and IoT devices.
Users connecting to the guest network located in the reception area are reporting slow performance. The network administrator is reviewing the information shown in the exhibits as part of the ongoing investigation of the problem. They show the profile used for the AP and the controller RF analysis output together with a screenshot of the GUI showing a summary of the AP and its neighboring APs.
To improve performance for the users connecting to the guest network in this area, which configuration change is most likely to improve performance?
- A. Increase the transmission power of the AP radios
- B. Enable frequency handoff on the AP to band steer clients
- C. Reduce the number of wireless networks being broadcast by the AP
- D. Install another AP in the reception area to improve available bandwidth
Answer: B
NEW QUESTION # 35
......
Authentic Best resources for NSE6_FWF-6.4 Online Practice Exam: https://passtorrent.testvalid.com/NSE6_FWF-6.4-valid-exam-test.html