[2024] Earn Quick And Easy Success With NSE6_FSW-7.2 Dumps
Free NSE6_FSW-7.2 pdf Files With Updated and Accurate Dumps Training
NEW QUESTION # 25
Exhibit.
The exhibit shows the current status of the ports on the managed FortiSwitch.
Access-1.
Why would FortiGate display a serial number in the Native VLAN column associated with the port23 entry?
- A. Ports connect to adjacent FortiSwitch devices will show their.serial number as the na-tive VLAN
- B. Port23 is a member of a trunk that uses the Access-1 FortiSwitch senal number as the name of the trunk.
- C. Port23 is configured as the dedicated management interface.
- D. A standalone switch with the showm serial number is connected on por123.
Answer: A
NEW QUESTION # 26
Which two statements about VLAN assignments on FortiSwitch ports are true? (Choose two.)
- A. Assign an IP address and subnet mask to FortiSwitch VLANs
- B. Assign untagged VLANs using FortiGate CLI
- C. Configure a native VLAN on the FortiLink
- D. Only assign one native VLAN on a port
Answer: B,D
NEW QUESTION # 27
What type of multimode transceiver can be used to split a 40G port?
- A. QSFP transceiver
- B. SFP+ transceiver
- C. QSFP+ transceiver
- D. SFP transceiver
Answer: C
NEW QUESTION # 28
Refer to the exhibit.
Core-1 and Access-1 are managed and authorized by FortiGate-1. which uses port4 as the FortiLink interface. After FortiGate authorizes and manages Core-2. Port1 status becomes STP discarding.
Why is port1 in the discarding state?
- A. Access-1 is the root bridge and can only have one root port.
- B. Core-2 has the lowest bridge priority.
- C. Core-1 and Core-2 do not have MCLAG configuration.
- D. port1 on Core-2 is discarding only management traffic.
Answer: C
NEW QUESTION # 29
Exhibit.
What conditions does a FortiSwitch need to have to successfully configure the options shown in the exhibit above? (Choose two.)
- A. The FortiSwitch model is equipped with a maximum of 54 interfaces.
- B. The CLI commands are enabling a splitpo rt into four 10Gbps interfaces.
- C. The split port can be assigned to native VLAN
- D. The port full speed prior the split was 100G SFP+
Answer: A,B
NEW QUESTION # 30
Exhibit.
LAG and MCLAG are used to increase the available network bandwidth and enable redundancy. How does spanning tree protocol see MCLAG and LAG if they are configured based on the physi-cal view shown in the exhibit? (Choose two)
- A. Switch 3 and switch 4 are seen as one MCLAG switch client
- B. Switch 1 and Switch 2 both seen as one single switch.
- C. Switch 1. Switch 2, and Switch 3 are seen as one MCLAG peer group
- D. Switch 3 and Switch 4 uplinks are treated as single interfaces.
Answer: A,B
NEW QUESTION # 31
Which two rules used by MSTP are similar to rules used by other STP methods? (Choose two.)
- A. MSTP uses alternate path and primary path, similar to regular STP.
- B. MSTP uses root bridge selection, similar to rapid STP
- C. MSTP uses port role election, similar to rapid STP on the instances.
- D. MSTP uses timers for transitioning the ports, similar to regular STP.
Answer: A,B
NEW QUESTION # 32
Which two statements about the FortiLink authorization process are true? (Choose two.)
- A. FortiLink authorization sets the FortiSwitch management mode to FortiLink.
- B. The administrator must manually pre-authorize FortiGate on FortiSwitch by adding the FortiGate serial number.
- C. A FortiLink frame is sent by FortiGate to FortiSwitch to complete the authorization.
- D. FortiSwitch requires a reboot to complete the authorization process.
Answer: A,C
NEW QUESTION # 33
Which interfaces on FortiSwitch send out FortiLink discovery frames by default in order to detect a FortiGate with an enabled FortiLink interface?
- A. The last four switch ports on FortiSwitch have auto-discovery enabled by default.
- B. The ports with auto-discovery enabled by default are dependent upon the FortiSwitch model.
- C. No ports are enabled by default for auto-discovery. This must be configured under config switch interface.
- D. All ports have auto-discovery enabled by default.
Answer: D
NEW QUESTION # 34
Refer to the exhibits
Traffic arriving on port2 on FortiSwitch is tagged with VLAN ID 10 and destined for PC1 connected on port1. PC1 expects to receive traffic untagged from port1 on FortiSwitch.
Which two configurations can you perform on FortiSwitch to ensure PC1 receives untagged traffic on port1? (Choose two.)
- A. Add the MAC address of PCI as a member of VLAN 10.
- B. Enable Private VLAN on VLAN 10 and add VLAN 20 as an isolated VLAN.
- C. Remove VLAN 10 from the allowed VLANs and add it to untagged VLANs on port1.
- D. Add VLAN ID 10 as a member of the untagged VLANs on port1.
Answer: A,D
NEW QUESTION # 35
Which QoS mechanism maps packets with specific CoS or DSCP markings to an egress queue?
- A. Classification for ingress traffic
- B. Marking for ingress traffic
- C. Queuing for egress traffic
- D. Rate limiting for egress traffic
Answer: A
NEW QUESTION # 36
Refer to the exhibit.
What two conclusions can be made regarding DHCP snooping configuration? (Choose two.)
- A. Maximum value to accept clients DHCP request is configured as per DHCP server range.
- B. DHCP clients that are trusted by DHCP snooping configured is only one.
- C. Global configuration for DHCP snooping is set to forward DHCP client requests on all ports in the VLAN.
- D. FortiSwitch is configured to trust DHCP replies coming on FortiLink interface.
Answer: B,D
NEW QUESTION # 37
Which packet capture method allows FortiSwitch to capture traffic on trunks and management interfaces?
- A. sFlow
- B. Sniffer profile
- C. TCP dump
- D. SPAN
Answer: A
NEW QUESTION # 38
Which statement about 802.1X security profiles using MAC-based authentication mode is true?
- A. FortiSwitch allows connectivity to all hosts connected to a port, if one host is authenticated.
- B. FortiSwitch can grant each device a different access level based on the credentials provided
- C. FortiSwitch performs faster when using this security mode on the ports.
- D. FortiSwitch must communicate with the RADIUS server to authenticate devices
Answer: B
NEW QUESTION # 39
How are the 'by VLAN redirect MAC address quarantine' mode and the 'by redirect MAC address quarantine' mode on FortiGate similar?
- A. Both modes require firewall policies to block inter-VLAN traffic.
- B. Both modes block intra-VLAN traffic by FortiGate automatically.
- C. Both modes add quarantined device MAC addresses to the blocked firewall address group.
- D. Both modes move quarantined devices to the quarantine VLAN.
Answer: B
NEW QUESTION # 40
To enhance service in emergency situations, to which LLDP-MED Type-Length-Values does Forti-Switch advertise to IP phones?
- A. Network policy
- B. Inventory management
- C. Power management
- D. Location
Answer: B
NEW QUESTION # 41
In which two ways can you assign a FortiSwitch port to a VDOM using multi-tenancy setup? (Choose two.)
- A. Create a virtual port pool on the FortiGate CLI.
- B. Remove the managed FortiSwitch and allocate ports directly on FortiSwitch.
- C. Assign a port to a VDOM directly on the managed FortiSwitch.
- D. Switch the FortiLink interface to the target VDOM.
Answer: A,C
NEW QUESTION # 42
Refer to the exhibit.
Which two statements best describe what is displayed in the FortiLink debug output shown in the exhibit? (Choose two.)
- A. FortiSwitch is in a waiting state to join the stack group on FortiGate.
- B. FortiSwitch is ready to push its new hostname to FortiGate.
- C. FortiSwitch is discovered and authorized by FortiGate.
- D. FortiSwitch is sending FortiLink heartbeats to FortiGate.
Answer: C,D
NEW QUESTION # 43
Which feature should you enable to reduce the number or unwanted IGMP reports processed by the IGMP querier?
- A. Enable the IGMP flood setting on the static port for all multicast groups.
- B. Enable IGMP flood unknown multicast traffic on the global setting.
- C. Enable the IGMP flood reports setting on the mRouter port.
- D. Enable IGMP snooping proxy.
Answer: D
NEW QUESTION # 44
......
Real Updated NSE6_FSW-7.2 Questions Pass Your Exam Easily: https://passtorrent.testvalid.com/NSE6_FSW-7.2-valid-exam-test.html